Catalysts are classified as homogeneous and heterogeneous. Homogeneous if they are present in the same phase as the reagent. This normally means that they are present as solutes in liquid reaction mixtures. Catalysts are heterogeneous if they are present in a different phase from that of the reactants. This normally means that they are present as solid with the reactants present either as gases or in solution. Both types of catalysis are discussed in this chapter and will be seen to be fundamentally similar.
From a practical standpoint, homogeneous catalysis is attractive because it is often highly selective towards the formation of a desired product. In large scale industrial processes, homogeneous catalysts are preferred for exothermic reactions because it is easier to dissipate heat from a solution than from the solid bed of a heterogeneous catalyst. In principle, every homogeneous catalyst molecule in solution is accesible to reagents, potentially leading to very high activities. It should also be borne in mind that the mechanism of homogeneous catalysis is more accesible to detail investigation than that of heterogeneous catalyst as species in solution are often easier to characterize than those on a surface and because the interpretation of rate data is frequently easier. The major disadvantage of homogeneous catalysts is that a separation step is required.
Heterogeneous catalysts are used very used extensively in industry and have a much greater economic impact than homogeneous catalysts. One attractive feature is that many of these solid catalysts are robust at high temperatures and therefore tolerate a wide range of opperating conditions. Reactions are faster at high temperatures, so at high temperatures solid catalysts generally produce higher outputs for a given amount of catalyst and reaction time than homogeneous catalysts operating at lower temperatures in solutions. Another reason for their widespread use is that extra steps are not needed to separate the product from the catalyst, resulting in effecient and more environtmentally friendly processes. Typically, gaseous or liquid reactants enter a tubular reactor at on end, pass over a bed of the catalyst, and products are collected at the other end. This same simplicity of design applies to the catalytic cenverter used to oxidize CO and hydrocarbons and reduce nitrogen oxides in automobile exhausts, Figure 1.
Figure 1. A heterogeneous catalyst in action. The automobile catalytic converter oxidized CO and hydrocarbons, and reduces nitrogen and sulfur oxides. The particles of a metal catalyst are supported on a robust, ceramic honeycomb.
Question:
Classify the following as homogeneous or heterogeneous catalysis and present your reasoning.
(a). The increased rate in the presence of NO(g) of SO2(g) oxidation by O2(g) to SO3(g)
(b). The hydrogenation of liquid vegetable oil using a finely divided nickel catalyst.
(c). The conversion of an aqueous solution of D-glucose to a D,L mixture catalysed by HCl(aq).
From a practical standpoint, homogeneous catalysis is attractive because it is often highly selective towards the formation of a desired product. In large scale industrial processes, homogeneous catalysts are preferred for exothermic reactions because it is easier to dissipate heat from a solution than from the solid bed of a heterogeneous catalyst. In principle, every homogeneous catalyst molecule in solution is accesible to reagents, potentially leading to very high activities. It should also be borne in mind that the mechanism of homogeneous catalysis is more accesible to detail investigation than that of heterogeneous catalyst as species in solution are often easier to characterize than those on a surface and because the interpretation of rate data is frequently easier. The major disadvantage of homogeneous catalysts is that a separation step is required.
Heterogeneous catalysts are used very used extensively in industry and have a much greater economic impact than homogeneous catalysts. One attractive feature is that many of these solid catalysts are robust at high temperatures and therefore tolerate a wide range of opperating conditions. Reactions are faster at high temperatures, so at high temperatures solid catalysts generally produce higher outputs for a given amount of catalyst and reaction time than homogeneous catalysts operating at lower temperatures in solutions. Another reason for their widespread use is that extra steps are not needed to separate the product from the catalyst, resulting in effecient and more environtmentally friendly processes. Typically, gaseous or liquid reactants enter a tubular reactor at on end, pass over a bed of the catalyst, and products are collected at the other end. This same simplicity of design applies to the catalytic cenverter used to oxidize CO and hydrocarbons and reduce nitrogen oxides in automobile exhausts, Figure 1.
Figure 1. A heterogeneous catalyst in action. The automobile catalytic converter oxidized CO and hydrocarbons, and reduces nitrogen and sulfur oxides. The particles of a metal catalyst are supported on a robust, ceramic honeycomb.
Question:
Classify the following as homogeneous or heterogeneous catalysis and present your reasoning.
(a). The increased rate in the presence of NO(g) of SO2(g) oxidation by O2(g) to SO3(g)
(b). The hydrogenation of liquid vegetable oil using a finely divided nickel catalyst.
(c). The conversion of an aqueous solution of D-glucose to a D,L mixture catalysed by HCl(aq).
loading...
0 Response to "Homogeneous and Heterogeneous Catalysts"
Post a Comment